Mastering Basic Plumbing for Installing a Bathtub
Mastering Basic Plumbing for Installing a Bathtub
Blog Article
Each person may have their personal opinion when it comes to A Step-by-Step Guide to Installing a Bathtub.
Setting up a bath tub isn't specifically brain surgery, yet it does require strong plumbing, woodworking, as well as often, tiling abilities. Replacing an old bathtub with a new one is also a moderately challenging job. If the old bathtub is conveniently obtainable, the project can relocate quickly; if you need to open up a wall surface to eliminate the old bathtub and place the brand-new tub, the job is a lot harder. In either instance, the project is within a residence handyman's skills, although you will require a helper to move out the old bathtub and also set in the new one. Make sure you have certified yourself for the task and also fit trying it. Rather than working with a professional to take control of a halfway-completed project, it is far better to take into consideration using one before you start. Possibilities are you may need a professional plumber to make tube links.
This article will certainly help you mount a brand-new tub in your washroom if you have already purchased a new tub and don't require to alter the arrangement of your previous water system pipelines.
Your devices as well as material list need to comprise the following:
Planning for the Installation
Firstly, the sustaining framework provided with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the tap comes with a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop strain on the tub.
Fit the flexible faucet ports to the bottom of both faucets making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make sure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its last placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain any kind of water remaining in the system. The process of eliminating the existing taps can be fairly bothersome due to the limited accessibility that is usually the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the taps. Have a cloth all set for the remaining water that will certainly originate from the pipes. Once the supply pipes have been eliminated, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this process. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any type of old securing compound.
Before proceeding to fit the new faucets, compare the pipeline links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Setting up the Tub
Making use of both wooden boards under its feet, place the bath tub in the called for placement. The wood boards are useful in equally spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to make sure that the bath tub is leveled all round. This can be achieved by checking the level and readjusting the feet on the tub till the level checks out degree.
To install faucets, fit the bottom of the outermost versatile faucet adapter to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water system and examine all joints and brand-new pipework for leakages as well as tighten them if essential. Load the tub as well as additionally inspect the overflow electrical outlet and also the regular outlet for leaks.
Ultimately, take care of the bathroom paneling as explained in the producer's user's manual. Tiling as well as sealing around the bathtub ought to wait till the bath tub has actually been made use of at the very least when as this will settle it into its final position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a link to the existing supply pipes.
If you need to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin making sure that the washers are in location between the tap as well as the sink. Safeguard the tap in place with the producer offered backnut. When the faucet is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous kind ought to be linked to the tap finishes first, tightening up just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bathroom satisfies the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to crack an inflexible seal, triggering the water to permeate the wall surface in between the bathroom and the tiling, causing problems with dampness as well as feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes as well as cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with spins of drenched paper or soft rope. Remember to constantly fill up the bathtub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can split relatively very early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally easily offered on the market. It is recommended to fit the floor tiles making use of waterproof or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious person who reads on Installing A Bathtub, I think sharing that excerpt was essential. Liked our piece? Please share it. Let someone else check it out. I enjoy reading our article about Installing A Bathtub.
Prioritize plumbing safety. Report this page